The RF401A is a 900 MHz radio designed for license-free use in several countries, including the United States and Canada. It provides a hassle-free way to create long-distance wireless links between your computer, data loggers, and measurement devices. The RF401A has a 910 to 918 MHz operating-frequency range and a configurable transmit-power output of 5 to 250 mW.
Campbell Scientific recommends the RF401A radios for existing installations that require compatibility with products such as the RF401, CR206X, CR211X, AVW206, and AVW211. For new installations, Campbell Scientific recommends using the RF407 or RF451.
Note: The image depicts the RF401A with an attached antenna. The antenna is sold separately.Read More
The RF401A is a frequency hopping spread spectrum radio designed for 900 MHz license-free ISM band operation. It has a 910 to 918 MHz operating-frequency range and a configurable transmit power output of 5 to 250 mW. It provides one of three selectable active connections including CS I/O, RS-232, and USB. It has a reverse polarity SMA (RPSMA) antenna jack connection. It is over the air compatible with legacy 9XStream products including the RF400, RF401, RF430, CR205, CR206(X), and AVW206.
|Radio Type||Frequency Hopping Spread Spectrum (FHSS)|
|Frequency||910 to 918 MHz|
|Country Used In||US, Canada|
|Power Output||5 to 250 mW (software-selectable)|
|Receiver Sensitivity||-109 dBm (Campbell Scientific protocols will issue retries wherever a bit error occurs.)|
|Channel Capacity||7 hop sequences share 25 frequencies.|
|RF Throughput Data Rate||9.6 kbps|
|Data Rate||10 kbps|
|Antenna Connector||Reverse Polarity SMA (RPSMA) jack|
|LEDs||Power on, Tx, Rx, diagnostics|
|RS-232 Baud Rate||1200 to 115200 bps|
|CS I/O Modes||SDC 7, 8, 10, 11, and ME master|
|Average Current Drain||
|Power||9 to 16 Vdc|
|Power Connector||2.5 mm DC power jack|
|Operating Temperature Range||
11.1 x 6.9 x 2.7 cm (4.4 x 2.7 x 1.1 in.)
Dimension are from the tip of antenna connector to other side of case, and from the bottom of case to the top of DB9 connector jack screw. The width includes the thickness of the screw heads on the screws that hold the case together.
|United States (FCC Part 15.247)||MCQ-XB900HP|
|Industry Canada (IC)||1846A-XB900HP|
The RF401A is over-the-air compatible with the RF401, RF430, CR206, CR206X, and AVW206.
The RF401A is also compatible with the RF400 and CR205, but the communication protocol must be set to transparent. Also, if RF400 and RF401A radios will be in the same RF proximity, do not use 28, 44, 52, 56, or 60 for the RF400 Net Address. RF400 radios with Net Addresses of 28, 44, 52, and 56 interfere with RF401A radios with Net Addresses of 0, 1, 2, and 3, respectively. The RF400 Net Address of 60 interferes with all RF401A Net Addresses.
Campbell Scientific does not recommend using the RF401A in networks containing FGR-115 or RF450 radios.
Do not mix RF401A radios using the Transparent protocol setting with RF401A, RF401, RF430, CR206(X), or AVW206 devices using a PakBus protocol setting. This will produce RF traffic without any RF communications. However radios with the PakBus Aware and PakBus Node settings can coexist in the same network.
|Data Logger||RS-232||CS I/O|
|Mixed-array data loggers||**|
*Use a 18663 null modem cable.
**It is possible to connect a mixed-array data logger (e.g., CR10, CR10X, CR23X, 21X, CR7) by using an SC932A or SC105 between the data logger's CS I/O port and the RF401A's RS-232 port.
Current RF401A and RF411A firmware. Requires the Device Configuration Utility.
A software utility used to download operating systems and set up Campbell Scientific hardware. Also will update PakBus Graph and the Network Planner if they have been installed previously by another Campbell Scientific software package.
Supported Operating Systems:
Windows 10, 8.1, 8, and 7 (Both 32 and 64 bit)
Number of FAQs related to RF401A: 19
Expand AllCollapse All
The COM220 and the RF401A can coexist on the CS I/O terminal, provided that they are assigned two different SDC addresses.
Yes. All antenna cables introduce a loss in the effective output of the system. The longer the antenna cable, the greater the loss.
There are many cavity- and notch-type filters available from third-party manufacturers.
There is a good chance that they would. However, the RF401A radios have been designed to work with Campbell Scientific data loggers. There are more generic spread-spectrum radios (off the shelf) that are designed to work in this type of configuration.
Use of the callback feature is handled under program control by the data logger and is not affected by the RF401A.
Yes, as do all radios. Adjacent radio equipment operating in the same frequency range can cause interference.
The RF401A can be powered either from a 12 Vdc source via the field power cable, or from a data logger via the CS I/O port.
Yes. The RF401A protocol needs to be set to transparent, which will communicate with the RF400 devices. However, if there are RF400 devices that are set to addresses of 28, 44, 52, 56, or 60, they must be changed when the RF401A radios are added to the network.
These radios ship with an SC12 serial cable and a 10873 RS-232 cable.